FREE BOOKS

Author's List




PREV.   NEXT  
|<   41   42   43   44   45   46   47   48   49   50   51   52   53   54   55   56   57   58   59   60   61   62   63   64   65  
66   67   68   69   70   71   72   73   74   75   76   77   78   79   80   81   82   83   84   85   86   87   88   89   90   >>   >|  
you are through using the axe, strike the blade into the top of the stump and leave the axe sticking there, where it will be safe from injury. Remember, before chopping down a tree or before using the axe at all, to see that there is enough space above and around you to enable you to swing the axe clear (Fig. 112) without the danger of striking bushes or overhanging branches which may deflect the blade and cause accidents more or less serious. Do not stand behind a tree as it falls (Fig. 115), for the boughs may strike those of a standing tree, causing the butt to shoot back or "kick," and many a woodsman has lost his life from the kick of a falling tree. Before chopping a tree down, select the place where it is to fall, a place where it will not be liable to lodge in another tree on its way down. Do not try to fell a tree against the wind. Cut a notch on the side of the tree facing the direction you wish it to fall (Fig. 113) and cut it half-way through the trunk. Make the notch, or kerf, large enough to avoid pinching your axe in it. If you discover that the notch is going to be too small, cut a new notch, _X_ (Fig. 116), some inches above your first one, then split off the piece _X_, _Y_ between the two notches, and again make the notch _X_, _Z_, and split off the piece _Z_, _W_, _Y_ (Fig. 116), until you make room for the axe to continue your chopping. When the first kerf is finished begin another one on the opposite side of the tree a little higher than the first one (Fig. 114). When the wood between the two notches becomes too small to support the weight of the tree, the top of the tree will begin to tremble and waver and give you plenty of time to step to one side before it falls. Fig. 112. Fig. 113. Fig. 114. Fig. 115. Fig. 116. Fig. 117. Fig. 118. [Illustration: How to "fall" a tree and how to take off the bark.] If the tree (Fig. 117) is inclined in the opposite direction from which you wish it to fall, it is sometimes possible (Fig. 117) to block up the kerf on the inclined side and then by driving the wedge over the block force the tree to fall in the direction desired; but if the tree inclines too far this cannot be done. There was a chestnut-tree standing close to my log house and leaning toward the building. Under ordinary circumstances felling this tree would cause it to strike the house with all the weight of its trunk and branches. When I told Siley Rosencranz I wanted that tree cut down
PREV.   NEXT  
|<   41   42   43   44   45   46   47   48   49   50   51   52   53   54   55   56   57   58   59   60   61   62   63   64   65  
66   67   68   69   70   71   72   73   74   75   76   77   78   79   80   81   82   83   84   85   86   87   88   89   90   >>   >|  



Top keywords:

direction

 
strike
 

chopping

 
weight
 

standing

 

inclined

 
branches
 

opposite

 

notches


higher

 

support

 
tremble
 

plenty

 

finished

 

desired

 

leaning

 

chestnut

 
building

Rosencranz

 

wanted

 

ordinary

 

circumstances

 

felling

 

Illustration

 

inclines

 
continue
 
driving

facing

 
deflect
 

accidents

 
overhanging
 

bushes

 

danger

 

striking

 
causing
 

boughs


sticking

 

injury

 
Remember
 

enable

 

pinching

 
discover
 

inches

 

woodsman

 

falling


liable
 

Before

 
select